How do I create a rocket?

There are thousands of different missile designs, there are the same number of ways to produce a missile. The fist step in making a rocket is to decide on a design that will largely affect costs. The most common way to build a rocket is the purchase of pre -billed sets; However, many builders decided to assemble from scratch. Several materials, including rough plate, double-sided tape and glue for spraying, as well as three wooden dowels in diameter of 0.75-, 0.50 and 0.25 inches (1.9-, 1.27- and 0.64-centimeter diameter) and a piece of maternity wood.

The first step towards making a rocket from zero is to assemble the body by lowering the poster to four equal rectangles, each measuring 11 inches (27.94 cm) by 14 inches (35.5 cm) long. Using a 0.25 -inch dowel (0.64 cm) to show both 11 inches (27.94 cm) edges of the crop with rolling desce around the dowel and rolling it. Then place the strip of double -sided tape along the length of one of the pre -rolled edges. NAnesthe even adhesive coating to the side of the plate opposite the side of the tape. The edge of the plate with the tape then rolls around the dowel of 0.75 inches (1.9 cm) towards the adhesive side until all the posters roll and form a cylindrical tube.

follow the above instructions using a poster 11 x 20 inches (27.94 x 50.8 cm) and dowels of 0.50 inches (1.27 cm) to form a second tube. Cut one inch (2.54 cm) from the end of this tube and place it in the body of the rocket. Apply the versatile glue around the inside of the body, approximately 3.5 inches (8.89 cm) from the bottom. Push the cut part of the tubing down the body until the adhesive is contacted. The lower part of the tube should be 3.5 inches (8.89 cm) from the bottom of the body.

The next step towards the production of the rocket is to create a fin. A piece of 12 inches (30.48 cm) by 1.5 -inch (3.81 cm) with 3/32 inches (0.24 cm) will be needed. Mark the point in the middle of the piece of wood as a link.Then mark the next point along the lower edge of the piece 1 inch from the left edge and one more point along the upper edge of 1 inch from the right edge.

Mark the last two points 1 inch (2.54 cm) from the center in the upper left and lower Dorub. Cut the wood diagonally from the lower left tag to the upper left and diagonally from the right lower mark into the upper right right brand to create fins. The initial edges of the fins to the sandpit point with a fine point with fine sand to improve aerodynamics. Use the universal adhesive to attach the fin in and intervals around the base of the body.

Use a piece of paper scratch 2 inches wide and 3 inches long and fold it around 1/8 -inch dowels to create a shot. The paper would be tied together with a versatile glue. Glue the vertical start vertically, next to one of the fin.

If you want to create a nasal cone, mark the middle point along the upper edge of the 3x5 index card. Left edge transport inward and oFine the right edge around the left and create a cone. Note that the nose of the cone should be placed at the mark made in the middle of the card.

Expand the cone until only the first fold made on the left side and apply the spray adhesive from the point where the left edge meets the card to the right edge. Re -establish the cone now that the adhesive is in place. Trim the excess paper from the bottom of the cone and make sure that the diameter of the cone is equal to 0.75 inches (1.9 cm). Use universal glue to secure the cone on the top of the body.

Apply a small amount of glue to the rocket engine cover and place the engine into the bottom of the rocket. Connect the lighter to the rocket engine through the plastic plug with the engine. If you want to make the rocket unique to your personality, apply the designs of color stickers or vinyl stickers for body and fin.

IN OTHER LANGUAGES

Was this article helpful? Thanks for the feedback Thanks for the feedback

How can we help? How can we help?