What Is a Wood Conveyor?
Wood shaving machine, also known as wood shaving machine, wood shaving machine, wood shaving machine, wood shaving machine, wood shaving equipment, wood shaving machine. Wood shaving machine is mainly used for batch production of thin wood shavings with uniform thickness. It is an automatic wood shaving machine. It includes a rack, a platform placed on the rack, a knife holder fixed on the platform, the wood enters the machine through the feed port, and the blade is sliced inside the machine to punch the shavings. The resulting shavings are uniform in size and thickness. There is no difference in hand-made shavings from the factory.
Wood shaving machine
- Chinese name
- Wood shaving machine
- Also known as
- Wood shaving machine
- Mainly used
- Mass production of flake shavings with uniform thickness
- Nature
- Automatic wood shaving machine
- Wood shaving machine, also known as wood shaving machine, wood shaving machine, wood shaving machine, wood shaving machine, wood shaving equipment, wood shaving machine. Wood shaving machine is mainly used for batch production of thin wood shavings with uniform thickness. It is an automatic wood shaving machine. It includes a rack, a platform placed on the rack, a knife holder fixed on the platform, the wood enters the machine through the feed port, and the blade is sliced inside the machine to punch the shavings. The resulting shavings are uniform in size and thickness. There is no difference in hand-made shavings from the factory.
- Can be used as particleboard (plywood), paper mills as raw materials for wood pulp paper, transportation companies as fragile transport fillings, for small pigs
- This machine can process logs, branches (branch), and board edges into shavings. The produced shavings are the same as the shavings produced by the furniture factory. The fully automatic feeding equipment greatly improves the production speed, and also saves time and labor.
- This machine is a device that automatically crushes and processes wood into wood shavings. After the raw materials enter through the feed port, they are first cut into the crushing chamber via a blade, cut by the impact of a high-speed rotating hammer and the use of a shearing knife. The wind generated by the leaves is sent through the screen outlet or the external fan. The size of the shavings is determined by adjusting the length of the blade and the size of the screen aperture to meet various needs.
- (1) The belt is easy to bite when the wood shaving shredder is used, because the motor rotor and the wood shredder rotor are not concentric. You can move the position of the motor left or right, or add pads under the motor feet to adjust the concentricity of the two rotors degree.
- (2) The output of wood shaving mill is relatively low. Reason: The blade is not sharp or the knife is not adjusted to the proper position. Solution: Remove the knife, grind the blade, and adjust the blade to a proper chip position.
- (3) The feeding is difficult, and the knife chip is laborious. Cause: The knife is severely worn, and the gap between the fixed knife is too large or too small. Solution: sharpen the blade to ensure the blade is sharp. Adjust the fixed knife clearance 2-3mm, the blade angle cannot be greater than 30 °.
- (4) The machine is feeding too fast. Reason: The feeding speed is uneven, and the blade is not sharp. Solution: Feed evenly to ensure that no material is stored in the crushing bin. Sharpen the blade to speed up the chip cutting speed.
- (5) The bearing is hot. Reason: There is no butter in the bearing seat, the bearing seat is not installed flat, and the bearing is damaged. The belt is installed too tightly. Solution: Add butter to the bearing, balance the bearing seat, replace with a new bearing, adjust the tension of the belt, and make the equipment work normally.
- (1) Adjust the tightness of the belt after use every day, and it is suitable to drop 6-10mm.
- (2) Clean the inside of the machine, and do not leave the last crushed material.
- (3) The bearing seat should be filled with butter in time, and the grease should be filled once for 3-4 hours of continuous work. Observe the observation.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|