What Is a Vertical Milling Machine?

Compared with the horizontal milling machine, the main difference between the vertical milling machine and the vertical milling machine is the vertical arrangement of the spindle. In addition to the different spindle layout, the table can be lifted up and down. End mills, chucks, drills, etc. can be used. It can mill keyway, plane, boring, etc. The horizontal milling machine can also use the above tools, but it is not as convenient as end milling. It is mainly possible to use a rack to enhance the strength of the tools (mainly three-sided edge milling cutters, sheet milling cutters, etc.). It can mill grooves, planes, and cut. Horizontal milling machines generally have end milling heads. Although this end milling head is not as powerful and rigid as a vertical milling machine, it is sufficient for end milling processing. This makes the overall function of horizontal milling machines more powerful than vertical milling machines. Vertical milling machines do not have this feature and cannot process workpieces suitable for horizontal milling. Productivity is higher than horizontal milling machines.

Product use: Suitable for processing planes, bevels, grooves, holes, etc. of various parts.

(1) Desktop milling machine: small

X5032 vertical milling machine spindle to the table distance (mm) 45 415

X5032 The distance from the centerline of the spindle of the vertical milling machine to the vertical rail of the bed (mm) 350

X5032 Spindle hole taper of vertical milling machine 7:24 ISO50

X5032 Vertical Milling Machine Spindle Aperture (mm) 29

X5032 vertical milling machine spindle speed (rpm) 18 levels 30 1500/18 levels

X5032 vertical milling machine vertical milling head maximum rotation angle ± 45 °

X5032 vertical milling spindle axial movement distance (mm) 85

X5032 vertical milling machine work surface (width x length) (mm) 320 x 1325

X5032 vertical milling machine table travel longitudinal / transverse / vertical (manual / motorized) (mm)

X5032 vertical milling machine 720/700, 255/240, 370/350

X5032 vertical milling machine table feed range longitudinal / transverse / vertical (mm / min)

X5032 vertical milling machine 23.5 1180 / 23.5 1180/8 394

X5032 vertical milling machine table rapid moving speed longitudinal / transverse / vertical (mm / min) 2300/2300/770

X5032 vertical milling machine T-slot number of slots / slot width / slot pitch (mm /) 3/18/70

X5032 vertical milling machine main motor power (mm) 7.5

X5032 vertical milling machine feed motor power (kw) 1.5

X5032 vertical milling machine dimensions (mm) 2530 × 1890 × 2380

X5032 vertical milling machine net weight (kg) 3200

Vertical milling machine milling head can be adjusted ± 45 ° clockwise and counterclockwise in the vertical plane; vertical milling machine X, Y, Z three-direction motorized feed; vertical milling machine spindle uses energy consumption braking, braking

In the vertical milling head of the vertical milling machine, the main wearing parts are the main shaft, the main shaft sleeve and the sleeve body hole. These parts can generally be used after being repaired without serious wear and failure. The repair methods of each wear part are as follows:

1,

Regulations for the operation of vertical milling machines

1. It is strictly prohibited for the operator to overload the equipment.

2. Before driving, you must check carefully according to the tour inspection points and lubricate according to the lubrication chart.

3. When stopping the machine for more than eight hours before starting the equipment, it should be rotated at a low speed for three to five minutes before confirming that the lubricating system is smooth and all parts are moving normally before starting work.

4. During use, do not leave or entrust others to take care of it, do not remove safety protection devices, do not remove dismantling iron.

5. Before moving the beam spindle workbench and lifting table, loosen the fastening screws, remove the surrounding debris, clean the guide rails and apply oil.

6. The speed limit iron should be adjusted first during fast or automatic feed.

7. The equipment must be frequently checked during operation, and the operation and lubrication of each department. If operation or lubrication is not good, stop using it.

8. It is forbidden to put work, measuring tools and workpieces on the work surface.

9. When adjusting the automatic cycle, you must check the correctness of the automatic cycle of the machine tool before driving.

10. When the work is completed, place the handles in the non-working position, the worktable in the middle position, the lifting platform falls below and cut off the power.

Maintenance measures for vertical milling machines

1. Before operating the machine tool, you should read the instruction manual of the machine tool, fully understand the technology and functions of the machine tool, and operate in the prescribed manner.

2. Wear closed overalls.

3. Always check whether there are any obstacles in or around the machine.

4. Do not operate the electrical equipment of the machine with wet hands.

5. Refer to the inspection sites of specifications in this manual, and inspect, adjust and maintain them regularly.

6. Do not disassemble or modify safety devices or signs and protective devices at will.